Your local HVAC experts in Pelham Manor, NY. From emergency repair to full system replacement, we handle every heating and cooling need.
Browse our full range of heating, cooling, and air quality services available in your area.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Air conditioning failures range from simple capacitor replacements to complex compressor and refrigerant circuit repairs requiring EPA Section 608 certified handling. Our technicians diagnose the root cause using superheat and subcooling measurements, amp draws, and pressure readings to restore full cooling output.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
In a village like Pelham Manor, word travels fast — and that is exactly how most of our customers find us. KIC Refrigeration has earned the trust of Pelham Manor property owners through years of delivering honest system evaluations, quality HVAC installations, and heating and cooling systems that keep families comfortable without inflated utility bills.
We believe the best advertising is a neighbor who stays comfortable all year. That is why every KIC Refrigeration project in Pelham Manor, NY is completed to the highest standard, backed by our workmanship warranty and manufacturer guarantees, and supported by a team that answers the phone when you call. Your trust is our most valuable asset.
Built on NATE certification, transparent pricing, and a guarantee that we stand behind.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
We help you select equipment with the highest SEER2, HSPF2, and AFUE ratings that fit your budget, and we install it to manufacturer specifications so you actually achieve rated efficiency. Proper charge, proper airflow, proper duct sealing — the details that turn rated efficiency into real savings.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Answers to the heating and cooling questions our customers ask most often.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Pelham Manor and surrounding New York communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
The ideal time for HVAC replacement in Pelham Manor is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in New York and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Pelham Manor including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
As a guideline for Pelham Manor homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
A comprehensive HVAC inspection from KIC Refrigeration in Pelham Manor covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Pelham Manor require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current New York mechanical codes and International Mechanical Code standards.
Hear what our customers have to say about the quality and reliability of our HVAC work.
"Solid air duct repair work. They sealed up several leaks in our ductwork and airflow improved throughout the whole house. Good value."
"Boiler kept cycling on and off. Technician found a faulty thermocouple and replaced it on the spot. No nonsense, no upselling. Just good honest work."
"KIC Refrigeration cleaned our dryer vent and also noticed our exhaust duct was damaged. Fixed both on the same visit. That kind of attention to detail matters."
Our NATE-certified crews provide HVAC service throughout the surrounding area.